Smart Key & Button Start Centennial / Equus Copyright 2009 All rights reserved. No part of this material may be reproduced, stored in any retrieval system. - презентация

1

2 Smart Key & Button Start Centennial / Equus Copyright 2009 All rights reserved. No part of this material may be reproduced, stored in any retrieval system or transmitted in any form or by any means without the written permission of Hyundai Motor Company.

3 2 Smart Key & Button Start Copyright 2009 All rights reserved. No part of this material may be reproduced, stored in any retrieval system or transmitted in any form or by any means without the written permission of Hyundai Motor Company. Main Features Passive Door Lock & Unlock : - Lock : button type, Unlock : touch sensor type ESCL (Electronic Steering Column Lock) : - Steering column lock and unlock by motor Passive Engine Start : (Registered smart key with driver) - Engine start by button (with pressing brake pedal & shift lever P position) - Ignition switch is operated by button (without pressing brake pedal) OFF ACC IG ON OFF Limp home for Engine Start : (Smart key battery discharged, Error of Smart Key system) - Smart key insert to key holder and press start button Welcome light : (using puddle lamp on outside mirror) - When a driver comes to vehicle with FOB key puddle lamp ON for 15 sec

4 3 Smart Key & Button Start Copyright 2009 All rights reserved. No part of this material may be reproduced, stored in any retrieval system or transmitted in any form or by any means without the written permission of Hyundai Motor Company. Button start changed things (BH vs. VI) UnitContentsBH 09MY IPM FOB Welcome light function, pre-authentication when puddle lamp works -Every 240ms for 4days / every 720ms for 10 days FOB searching Not applied IPM Capacitor sensor and lock button installed in 4 door Handle -No response if push the capacitor sensor while all doors are unlocked Not applied IPM Passive lock at trunk -Trunk trim switch & lock switch are applied in power trunk equipped vehicle -All doors are locked and trunk is locked when push trunk lock button with FOB Not applied IPM Door lock warning 3 times at FOB-in -BH: No response when try passive lock while FOB in the holder -VI : External buzzer works for 5sec at same condition Applied IPM ESCL Unit Status added (Service ability improved) -Unit status : OK/Retry/working Applied IPM SSB inhibition -Engine start inhibited for 1 sec after engine off with pushing 3 times within 3sec (over 5kph) Applied

5 4 Smart Key & Button Start Copyright 2009 All rights reserved. No part of this material may be reproduced, stored in any retrieval system or transmitted in any form or by any means without the written permission of Hyundai Motor Company. Smart key RF Receiver Door handle ( 4EA) Antenna (5EA) Bumper antenna (1EA) Trunk S/W IPM + Smart Key ECM Start button ESCL Cluster PDM 7 8 External Buzzer EMS PDM Relay 11 ESC 16 System Layout Smart key holder 9

6 5 Smart Key & Button Start Copyright 2009 All rights reserved. No part of this material may be reproduced, stored in any retrieval system or transmitted in any form or by any means without the written permission of Hyundai Motor Company. Components – IPM (Instrument Panel Module) IPM PDM RF Receiver Internal antenna #1 Internal antenna #2 1Operate antenna for searching smart key inside or outside : LF (Low Frequency) 2Receive smart key information from external receiver 3Control PDM relay and ignition switch : CAN with PDM 4Control ESCL LOCK/UNLOCK : Serial communication with ESCL 5Immobilizer function : communicate with PCM (ECM ; Engine Control Module) 6Warning error of smart key : buzzer and display information on cluster 7Communication gate with diagnosis tools 8Control BCM functions (ATWS, Wiper, Lamps... so on) with FAM (Front Area Module)

7 6 Smart Key & Button Start Copyright 2009 All rights reserved. No part of this material may be reproduced, stored in any retrieval system or transmitted in any form or by any means without the written permission of Hyundai Motor Company. Components – PDM (Power Distribution Module) PDM SSB (Start Stop Button) FOB Holder Nut 1ACC, IGN1, IGN2 and Starter relay control and failure detection (Current failure only) 2ESCL power and ground control and failure detection (Current and old failure) 3Check ESCL Unlock status via L_ESCL_UNLOCK (check Unlock or Not Unlock) 4Transponder communication via FOB holder (Immo_data, Immo_clock) 5SSB Amber, Blue (Green) LED and character illumination control 6 In order to prevent unexpected operation, PDM use 2 MCU. (Prevent unintended ESCL operation or Engine OFF so on) 7Use 2 Battery line with each connector (A10 Vbat_load and B20 Vbat_cpu are connected with both MCU)

8 7 Smart Key & Button Start Copyright 2009 All rights reserved. No part of this material may be reproduced, stored in any retrieval system or transmitted in any form or by any means without the written permission of Hyundai Motor Company. IPM can detect FOB in only reserved area via antenna. Uses ASK (Amplitude shift keying), 125Khz frequency, to precisely clarify distinction of acre 2 interior antennae (2 IPM output) 2 Rear package tray antennae (1 IPM output) 1 Trunk antenna 1 Bumper antenna 4 door handle antenna Trunk Bumper Interior Hat Shelf Passenger side Driver side Components – LF antennae (Detection range)

9 8 Smart Key & Button Start Copyright 2009 All rights reserved. No part of this material may be reproduced, stored in any retrieval system or transmitted in any form or by any means without the written permission of Hyundai Motor Company. Components – Antenna position Nut Bolt In case of Smart Key system isnt applied, block 3 holes by pad Nut Internal Antenna 1Internal Antenna 2Trunk Antenna Function : - Antenna for searching smart key in cabin Function : - Antenna for searching smart key in trunk Caution - Dont change the direction of antenna - Confirm the connection of connector

10 9 Smart Key & Button Start Copyright 2009 All rights reserved. No part of this material may be reproduced, stored in any retrieval system or transmitted in any form or by any means without the written permission of Hyundai Motor Company. Components – Antenna position Bolt In case of Smart Key system isnt applied, block 6 holes by pad Package Tray Antenna 1, 2Bumper Antenna Function : - Antenna for searching smart key upper side of package tray Function : waterproof type - Antenna for searching smart key outside of trunk Caution - Dont change the direction of antenna - Confirm the connection of connector Caution - Dont change the direction of antenna - Confirm the connection of connector - Dont exchange antenna for inside Screw

11 10 Smart Key & Button Start Copyright 2009 All rights reserved. No part of this material may be reproduced, stored in any retrieval system or transmitted in any form or by any means without the written permission of Hyundai Motor Company. ESCL Module Lock bolt Components – ESCL (Electronic Steering Column Lock) Stroke Bolt & Magnet Hall Sensor (Unlock Position) Micro Switch (Unlock Switch) ESCL Controller 6 pin connector (use 5 pin) Cover Worm Gear Helical Gear Motor Main Guide Lock Bolt Lock Bolt Cover Hall Sensor (Lock Position) Steering column lock / unlock : DC Motor Lock Bolt Serial Communication with IPM and Enable input from IPM Input and output status (lock/unlock) and ESCL operation order Receive power from PDM & Output signal of ESCL unlock switch PDM

12 11 Smart Key & Button Start Copyright 2009 All rights reserved. No part of this material may be reproduced, stored in any retrieval system or transmitted in any form or by any means without the written permission of Hyundai Motor Company. Unlock position Lock position Unlock procedure Lock procedure Lock Hall Sensor Unlock Hall Sensor Micro Sensor HIGH Hall Sensor Micro Switch Components – ESCL operation

13 12 Smart Key & Button Start Copyright 2009 All rights reserved. No part of this material may be reproduced, stored in any retrieval system or transmitted in any form or by any means without the written permission of Hyundai Motor Company. Control Ignition and engine ON/OFF by Sending signal to IPM and PDM Display status by LED Lamp ON/OFF (Amber or Blue) Components – Start Button NoIgnition conditionsStart Button LED status 1IG OFFLED OFF 2IG ACCAmber color LED ON 3IG ON (Engine OFF)Blue color LED ON (Pin name is Green) 4CrankingMaintain LED status before cranking 5Engine runningLED OFF NoCharacter lampConditions 1Indicator Lamp ONDoor open, Tail lamp ON, ACC, IG ON 2 Indicator Lamp 30sec ON Lamp OFF Door close, Tail lamp OFF, IG OFF 3Indicator Lamp OFFRemote LOCK, Passive LOCK 4Rheostat at tail lamp ON (Illumination lamp) Indicator ON/OFF condition at ignition key off condition Indicator ON/OFF condition according to Ignition key's position

14 13 Smart Key & Button Start Copyright 2009 All rights reserved. No part of this material may be reproduced, stored in any retrieval system or transmitted in any form or by any means without the written permission of Hyundai Motor Company. LED Components – Smart key Holder Send transponder information to PDM (Limp home start) Display system information by LED ON/OFF Smart key IN Switch is installed inside. Send smart key insert or pull put signal to PDM Smart key IN Switch Free lock position (S/Key IN Switch OFF) Lock position (S/Key IN Switch ON) Smart key Holder Transponder communication Demodulator (PCB ) Transponder Serial comm. Antenna Coil PDM

15 14 Smart Key & Button Start Copyright 2009 All rights reserved. No part of this material may be reproduced, stored in any retrieval system or transmitted in any form or by any means without the written permission of Hyundai Motor Company. IGN. Position Shift Lever Position P PositionN PositionOther Position (D or R) PushBrake + PushOver 1HRPushBrake + PushPushBrake + Push Off ACC. IG1 & 2 Start Condition of stop engine while driving - Press 3 times button within s seconds. - Press button more than 2 seconds The shift of Ignition Position Transfer possibility, after Smart key certification Transfer possibility without Smart key certification

16 15 Smart Key & Button Start Copyright 2009 All rights reserved. No part of this material may be reproduced, stored in any retrieval system or transmitted in any form or by any means without the written permission of Hyundai Motor Company. Passive Access Example Pre-condition : All Doors are locked and Closed IPM sends "All Doors Unlock" command to DDM NA option case : "Driver door Unlock" command Response RF Down- Link SRx Touch Challenge LF Up- Link General searching procedure

17 16 Smart Key & Button Start Copyright 2009 All rights reserved. No part of this material may be reproduced, stored in any retrieval system or transmitted in any form or by any means without the written permission of Hyundai Motor Company. Passive Door Unlock Challenge LF Up-Link Smart Key module issues on the CAN the passive access command Receiver ESCL LF RF Unlock command Touch IPM Smart Key Function Smart Key module = IPM

18 17 Smart Key & Button Start Copyright 2009 All rights reserved. No part of this material may be reproduced, stored in any retrieval system or transmitted in any form or by any means without the written permission of Hyundai Motor Company. Passive Door Lock Challenge LF Up-Link Smart Key module issues on the CAN the passive access command Push button LF RF Lock command IPM Smart Key Function ESCL Receiver

19 18 Smart Key & Button Start Copyright 2009 All rights reserved. No part of this material may be reproduced, stored in any retrieval system or transmitted in any form or by any means without the written permission of Hyundai Motor Company. After pressing start button, searching smart key in the cabin. If Smart Key module (IPM) is searched, it is authentication. After authenticating, ESCL is unlocked command. After authenticating at ignition on, authentication is maintained. Searching procedure : if IPM found FOB, IPM stop next searching. User action : User Press SSB 1 st interior Searching Authentication is valid Possible to ESCL Unlock Possible to Ignition ON Possible to start (EMS ECM) No needed to search inside Passive Start Authentication Smart Key Function 1 st Interior searching 2 nd Interior searching 1 st Rear Package tray searching TP searching If no valid FOB found, IPM issues Auth failed warning 2 nd interior Searching R/P tray searching

20 19 Smart Key & Button Start Copyright 2009 All rights reserved. No part of this material may be reproduced, stored in any retrieval system or transmitted in any form or by any means without the written permission of Hyundai Motor Company. Welcome light Smart Key Function IPM search for smart key through door handle antenna operating every 240ms When smart key approach to door handle antenna send information to receiver Receiver send signal to IPM IPM ON signal to DDM, ADM after smart key authentication Puddle lamp (driver and passenger side) are ON for 15sec LF Receiver IPM 2 3 DDM ADM 4 4 1

21 20 Smart Key & Button Start Copyright 2009 All rights reserved. No part of this material may be reproduced, stored in any retrieval system or transmitted in any form or by any means without the written permission of Hyundai Motor Company. Block Diagram StarterACC IGN1 IGN2 Relay Box IPM + Smart Key ECM IPM + Smart Key ECM LF Driver Engine ECM Engine ECM Serial Comm. Diagnosis Tool ESC FAM DDM. FAM DDM. Body CAN PDM LF Antenna RF Receiver ESCL Smart Key Wireless Comm. (125Khz) Radio Frequency (315/433/447Mhz) ESCL Power ESCL Ground Unlock Switch Serial Comm. Smart Key Holder Data Smart Key IN Switch Clock Start Button Start Button S/W ON Signal 2 LED control ESCL enable signal Transponder Communication Illumination Serial Comm. (9.6kbps) Vehicle Speed K-line KWP2000(10.4kbps) Cluster 1 line Wire Power - train CAN Engine rpm signal S/W ON Signal 1 Brake S/W P position

22 21 Smart Key & Button Start Copyright 2009 All rights reserved. No part of this material may be reproduced, stored in any retrieval system or transmitted in any form or by any means without the written permission of Hyundai Motor Company. Control Function - Passive Lock & Unlock - Passive ENG. Start Power - train CAN Procedure of passive operation - Door Unlock: Door button S/W ab cda I - Door lock: Door button S/W ab cd a I - ENG. Start: h a & e b c d a e f a & e S/relay IPM + Smart Key ECM IPM + Smart Key ECM LF Driver Engine ECM Engine ECM Serial Comm. Diagnosis Tool ESC FAM DDM FAM DDM Body CAN PDM LF Antenna RF Receiver ESCL Smart Key Wireless Comm. (125Khz) Radio Frequency (315/433/447Mhz) ESCL Power ESCL Ground Unlock Switch Serial Comm. Smart Key Holder Data Smart Key IN Switch Clock Start Button Start Button S/W ON Signal 2 LED control ESCL enable signal Transponder Communication Illumination Serial Comm. (9.6kbps) Vehicle Speed K-line KWP2000(10.4kbps) Cluster 1 line Wire Engine rpm signal S/W ON Signal 1 StarterACC IGN1 IGN2 Relay Box Brake S/W P position

23 22 Smart Key & Button Start Copyright 2009 All rights reserved. No part of this material may be reproduced, stored in any retrieval system or transmitted in any form or by any means without the written permission of Hyundai Motor Company. IPM PDM ESCL Cluster SSB 1. User press SSB with valid FOB 2. IPM starts FOB searching and send ESCL power ON command to PDM 3. PDM supplies ESCL Bat and GND 4. IPM found valid FOB and checked ESCL locked state 5. IPM sends "Unlock" command to ESCL 6. ESCL operate Unlocking and send operation finished information to IPM. 7. IPM sends "ESCL power OFF and transit to Start" command to PDM 8. PDM turn ESCL bat and GND off, and then turn IGN1 relay on. After 50ms later, turn Starter relay on. Cranking!!! Engine Control Module (ECM) 9. Immobilizer communication between ECM and IPM via serial line 10. ECM sends Engine running information to IPM (C-CAN -> Cluster-> B-CAN -> IPM) 11. IPM send "transit to Running" command to PDM Engine is Running by just one SSB pressing!!! Simple explanation : One touch cranking Cluster-> B-CAN -> IPM) 11. IPM send "transit to Running" command to PDM Engine is Running by just one SSB pressing!!! Simple explanation : One touch cranking">

24 23 Smart Key & Button Start Copyright 2009 All rights reserved. No part of this material may be reproduced, stored in any retrieval system or transmitted in any form or by any means without the written permission of Hyundai Motor Company. Phenomenon by problem in circuit 1 Problem casePhenomenon Body CAN BUS Hi & Lo line open or short to ground Impossibility of engine cranking rpm signal defect (PDM receive signal) P/Train CAN Normal + PDM rpm signal fail + CAN gate Cluster disconnected - Cranking is possible but Starter motor can be burned. - Engine is running, but IPM doesn't know it. So PDM keep Starter relay on state for 10s~25s depending on temperature. P/Train CAN abnormal + PDM rpm signal fail + CAN gate Cluster connected - Same with above P/Train CAN normal + PDM rpm signal fail + CAN gate Cluster connected Normal SSB switch signal 1 or 2 defected SSB signal 1 or 2 defected Change to fail safe mode : Cranking is possible with twice press start button. And, Press start again message display on cluster Both SSB signals are defectedCranking impossible Serial communication signal defected between ECM and IPM - Impassible Engine ON - 1 st cranking trial : Engine is Running and stop - After 2 nd cranking trial : Keep cranking for 10s~25s. Serial communication signal defected between RF receiver and IPM. Starting possible by FOB insert to FOB holder. If FOB is not in, IPM can not search Smart key, and (For 1 st trial, Key is not detected / more than 2 nd trial : "insert FOB in FOB holder" message display on cluster.

25 24 Smart Key & Button Start Copyright 2009 All rights reserved. No part of this material may be reproduced, stored in any retrieval system or transmitted in any form or by any means without the written permission of Hyundai Motor Company. Problem casePhenomenon Serial communication defected between IPM and ESCL (IPM Pin No C05) Cranking is impossible in case of ESCL state is lock, Thus, Starting is available in state that unlock signal is inputted to PDM At this time, Check steering wheel lock massage display on cluster (set "ESCL failure" DTC) Unlock Switch signal defected between PDM and ESCL (Micro switch) - ESCL release checking is impossible by IPM and PDM. So any transition are not allowed. - At this time, Check steering wheel lock massage display on cluster - But only ESCL locking can be done. -(set "ESCL failure" DTC) Enable signal defected between IPM & ESCL (IPM B17 pin) -If ESCL is already Unlocked, then cranking is possible. But if user any door open/close or RKE lock or Passive lock or FOB remove from FOB holder, then Check steering wheel lock massage display on cluster -If ESCL is Locked, Check steering wheel lock massage display on cluster when user press SSB button. -(set "ESCL failure" DTC) PDM Vbat_Load fuse (25A) failed or PDM ESCL bat (A04) or ESCL GND (A05) Pin is defected. When user press SSB, Check steering wheel lock massage display on cluster. (set "ESCL failure" DTC) Not receive for brake switch signal Change to fail safe mode : Starting is available though press engine start button more than 10 seconds. Phenomenon by problem in circuit 2

26 25 Smart Key & Button Start Copyright 2009 All rights reserved. No part of this material may be reproduced, stored in any retrieval system or transmitted in any form or by any means without the written permission of Hyundai Motor Company. Pre-Authentication : It is for engine start quickly. (minimize reaction time) - Smart Key Module (IPM) try to find valid FOB and check ESCL status. If smart key is detected, maintain the authentication without detecting smart key again And memorized latest ESCL status during authentication. 1. Driver side door is opening : Try to find smart key every 3seconds via only int. antennae Smart Key is found (maintain authentication), Smart key isnt found (cancel authentication) 2. Driver side door is closing : Try to find Smart key via only int. antenna2 Smart key is found (Maintain authentication during 30 seconds. IPM dont try to find again 3. Press brake pedal : Try to find smart key via int. antennae Smart key is found (Maintain authentication during 30 seconds.) 4. IG is OFF : Try to find smart key via int. antennae Smart key is found (Maintain authentication during 30 seconds.) Pre-authentication isnt related with immobilizer lamp Control Function – Pre-Authentication

27 26 Smart Key & Button Start Copyright 2009 All rights reserved. No part of this material may be reproduced, stored in any retrieval system or transmitted in any form or by any means without the written permission of Hyundai Motor Company. Conditions ACC or IGN 1 ON Key in not activate VSS is less than 3km/h Conditions ACC or IGN 1 ON Key in not activate VSS is less than 3km/h 1. Door is opened 3. Searching Smart key 2. Smart Key located at outside Warning Information on Cluster – Smart Key out warning (Door is opening) Objective : Prevent for leaving at ACC or IG ON position. - If door is opening at ACC or IG ON position, searching smart key every 3 seconds. - Smart key isnt inside Display message on cluster and internal buzzer warning ON. 4. Buzzer warning & display Information on Cluster

28 27 Smart Key & Button Start Copyright 2009 All rights reserved. No part of this material may be reproduced, stored in any retrieval system or transmitted in any form or by any means without the written permission of Hyundai Motor Company. Warning Information on Cluster – Smart Key out warning (Door is closing) Objective : Prevent for leaving at ACC or IG ON. When door is closing at ACC or IG ON position, searching smart key. - Smart Key is inside No action (Normal) - Smart Key isnt inside Warning Information display message on Cluster Internal / external buzzer are warning (5seconds) Searching smart key every 3 seconds Activate Internal Buzzer 5 seconds Conditions ACC or IGN 1 ON Key in not activate VSS is less than 3km/h Conditions ACC or IGN 1 ON Key in not activate VSS is less than 3km/h 2. Door is closing 1. Door is opened (Min. 1 door) Activate External Buzzer 5 seconds 3. Searching Smart key 4. Smart Key located at outside 5. Internal / external buzzer are warning (5seconds)

29 28 Smart Key & Button Start Copyright 2009 All rights reserved. No part of this material may be reproduced, stored in any retrieval system or transmitted in any form or by any means without the written permission of Hyundai Motor Company. Warning Information on Cluster – ESCL NOT LOCK WARNING Objective : When ESCL or P- Position S/W is problem, for informing to customer. - Internal buzzer is warning (Continuously) during driver door opening. - If all doors are closing or ACC or IG is ON, Stop the warning 2. Checked status of ESCL 3. ESCL is unlocked 4. ESCL not lock warning IPM Activate Internal Buzzer Conditions ACC or IGN 1 OFF Key in not activate VSS is less than 3km/h Conditions ACC or IGN 1 OFF Key in not activate VSS is less than 3km/h 1. Driver side door is opening

30 29 Smart Key & Button Start Copyright 2009 All rights reserved. No part of this material may be reproduced, stored in any retrieval system or transmitted in any form or by any means without the written permission of Hyundai Motor Company. Warning Information on Cluster – ESCL NOT UNLOCK WARNING Objective : When ESCL dont unlock, for re-trying or checking the system. - Display message on Cluster - blinking start button LED (Green color 10 sec) - Internal buzzer (once) IPM Activate Internal Buzzer

31 30 Smart Key & Button Start Copyright 2009 All rights reserved. No part of this material may be reproduced, stored in any retrieval system or transmitted in any form or by any means without the written permission of Hyundai Motor Company. Warning Information on Cluster – ESCL is malfunction Objective : If ESCL is malfunction, engine start and ignition on are impossible This is memorized failure code and This is hole system failure related with ESCL (wire failure or fuse failure or communication failure or ESCL component failure) Conditions : ESCL send fail signal to IPM, ESCL isnt controlled. - Display message on Cluster - blinking start button LED (Amber color 10 sec) - Internal buzzer ( 3 sec) IPM Activate Internal Buzzer (3sec)

32 31 Smart Key & Button Start Copyright 2009 All rights reserved. No part of this material may be reproduced, stored in any retrieval system or transmitted in any form or by any means without the written permission of Hyundai Motor Company. Key Reminder 1 Objective : It is for preventing door lock (smart key is inside) Conditions : Any door is opened, smart key is inside, Any door lock knob are changed from Unlock to Lock - All doors should be unlocked 1. Any door is opened ACC or IGN 1 OFF Key in not activate 2. Changed Unlock to Lock by door lock knob or RKE or Central Lock button 4. Found smart key inside 5. Sending key reminder unlock signal (IPM DDM) 6. All doors unlock 3. Searching the smart key

33 32 Smart Key & Button Start Copyright 2009 All rights reserved. No part of this material may be reproduced, stored in any retrieval system or transmitted in any form or by any means without the written permission of Hyundai Motor Company. Key Reminder 2 Objective : It is for preventing door lock (smart key is inside) Conditions : Any door is opened, smart key is inside All doors are closed and All doors are locked within 500ms. - All doors should be unlocked 1. All doors are closed ACC or IGN 1 OFF Key in not activate 2. All doors are locked within 500ms 4. Found smart key inside 5. Sending key reminder unlock signal (IPM DDM) 6. All doors unlock 3. Searching the smart key Remark (500ms timer) - Just after all doors closed, if all doors are locked and FOB is detected in interior : IPM consider this Unintended locking. Activate External Buzzer ( 5 sec )

34 33 Smart Key & Button Start Copyright 2009 All rights reserved. No part of this material may be reproduced, stored in any retrieval system or transmitted in any form or by any means without the written permission of Hyundai Motor Company. Door lock warning 1 Objective : To prevent driver leaving after passive door lock at IG ON or ACC position Conditions : IG ON or ACC position and passive door lock - Impossible passive door lock - External buzzer (3 sec) Driver push the button Receiver Push button ACC or IGN 1 On Key in not activate ACC or IGN 1 On Key in not activate Activate External Buzzer ( 5 sec )

35 34 Smart Key & Button Start Copyright 2009 All rights reserved. No part of this material may be reproduced, stored in any retrieval system or transmitted in any form or by any means without the written permission of Hyundai Motor Company. Door lock warning 2 Objective : To prevent driver leaving after passive door lock with opened door. Conditions : IG OFF, At least one door is opened and passive door lock - Impossible passive door lock - External buzzer (3 sec) Driver push the button Receiver Push button Activate External Buzzer ( 5 sec ) At least one door open

36 35 Smart Key & Button Start Copyright 2009 All rights reserved. No part of this material may be reproduced, stored in any retrieval system or transmitted in any form or by any means without the written permission of Hyundai Motor Company. Door lock warning 3 Objective : To prevent driver leaving after passive door lock with smart key inside. Conditions : IG OFF position, All doors are closed and passive door lock with one of smart key located in cabin - Impossible passive door lock (possible to lock by Smart Key and key) - External buzzer (3 sec) Driver push the button Receiver Push button Activate External Buzzer ( 5 sec ) Smart key 1 Smart key 2 IG OFF All doors are closed IG OFF All doors are closed

37 36 Smart Key & Button Start Copyright 2009 All rights reserved. No part of this material may be reproduced, stored in any retrieval system or transmitted in any form or by any means without the written permission of Hyundai Motor Company. Trunk warning Objective : To prevent driver closing trunk with smart key in trunk. Conditions : Smart key in trunk and trunk is closed (latch lock) - External buzzer (5 sec) and user can open trunk without fob for only next trunk open trial. Driver close trunk Activate External Buzzer ( 5 sec ) Smart key

38 37 Smart Key & Button Start Copyright 2009 All rights reserved. No part of this material may be reproduced, stored in any retrieval system or transmitted in any form or by any means without the written permission of Hyundai Motor Company. Smart key battery warning Objective : It is inform that Smart key battery is discharged. Conditions : IG OFF and smart key battery is lower. - Display message on cluster (10sec) and internal buzzer (once) Activate Internal Buzzer (Once ) 1. Searching smart key When IG OFF 2. Detected smart key battery low 3. IPM operate buzzer and send message to cluster

39 38 Smart Key & Button Start Copyright 2009 All rights reserved. No part of this material may be reproduced, stored in any retrieval system or transmitted in any form or by any means without the written permission of Hyundai Motor Company. Authentication fail Objective : It is inform that smart key authentication is failed. (insert smart key to holder) Conditions : Start button on and authenticated Smart Key isnt inside. - Display message on cluster (10sec) - Immobilizer lamp is blinking ( 10 sec) - Smart key holder LED is on (10 sec) Operated Start button once ++ Smart Key holder LED ON (10sec) Operated Start button twice

40 39 Smart Key & Button Start Copyright 2009 All rights reserved. No part of this material may be reproduced, stored in any retrieval system or transmitted in any form or by any means without the written permission of Hyundai Motor Company. Message for starting Objective : It informs that press foot brake pedal to start engine. Conditions : Push start button several times. (Start button condition is change to ACC over twice) - Display message on cluster (10 sec) Other warnings

41 40 Smart Key & Button Start Copyright 2009 All rights reserved. No part of this material may be reproduced, stored in any retrieval system or transmitted in any form or by any means without the written permission of Hyundai Motor Company. It is for starting at virgin condition All related parts are virgin condition (Smart key, IPM, PDM, ESCL ECM) ESCL is always unlock at virgin When virgin smart key is inserted in smart key holder, possible to start, IG ON and ACC position After inserting virgin smart key to holder, push start button once. - PDM perform twice ignition automatically If ECM is virgin, possible to twice ignition Twice ignition 1 s Cranking phase OFF ON IGN1 1 s

42 41 Smart Key & Button Start Copyright 2009 All rights reserved. No part of this material may be reproduced, stored in any retrieval system or transmitted in any form or by any means without the written permission of Hyundai Motor Company. IPM start to learn Smart key #2 learnt Input the PIN code PDM start to learn Smart key #1 learnt IPM/PDM/ESCL/Smart key #1 be learnt Pull out smart key #1 Insert smart key #2 to holder Insert smart key #1 to key holder ESCL start to learn IPM, PDM, ESCL and FOB #1 be learnt after 1 st key teaching is done at the same time. If teaching is failed before 1 st key teaching, each components are become previous state. (virgin or neutralized or learnt) But 2 nd key teaching is done independently. Neutralization mode is for replacing IPM ESCL.PDM ECM easily. It is possible that smart key is learnt again, after neutralizing Smart Key system. Virgin start (twice ignition) is impossible in neutralized condition If PIN code is inputted over 3 times, it is impossible to learnt and neutralization during 1 hour. If you reset battery, you should wait 1 hour again. Smart key teaching IPM, PDM and ESCL are connected. Terminal state are OFF and FOB holder is connected and FOB-in If you try to teach when above conditions are not fulfilled, "conditions are not correct" will be displayed via tool monitor.