Introduction R = ct/2 meters. RADAR. RADAR- Radio Detection and Ranging Coined by US Navy Usage Higher the frequency better the result Theory of reflection. - презентация

1 Introduction R = ct/2 meters. RADAR

2 RADAR- Radio Detection and Ranging Coined by US Navy Usage Higher the frequency better the result Theory of reflection (Absorbtion and re-radiation) Location parameters: Range, height, direction, direction of motion, relative velocity High transmitter power requirement Suitable oscillator: Magnetron

3 Applications Navigational aid on ground and sea Radar altimeters (height measurement) Radar blind lander (aircraft landing during poor visibility) Airborne radar for satellite surveillance Space applications like planetary observations Police radars (Law enforcement and Highway safety) Radars for determining speed of moving targets Remote sensing (weather monitoring) Air traffic control (ATC) and Aircraft safety Ship safety Non-contact method of speed and distance in industry

4 Military Applications: Detection and ranging of enemy targets even at night Aiming guns at aircrafts and ships Bombing ships, aircrafts, or cities even during night Early warning regarding approaching aircrafts or ships Directing guided missiles Searching for submarines, land masses and buoys

5 Radar block digram Bistatic radar Transmitter antenna Receiver antenna

6 Monostatic radar

7 The distance of the target can be calculated from the total time (t) taken by the pulse to travel to the target and return to its original initial point. Assuming c to be the velocity of light in free space, the distance traversed by pulse is ct meters. Now this is 2 times the target distance, hence the distance to the target R = ct/2 meters.

8 Requirements Automatically operating duplexer Tx should remain silent during echo period Tx pulse should be very powerful Rx should be highly sensitive to echo signals and should be highly immune to noise Antenna should be highly directive with large gain Pulse repetition frequency (prf) should be high compared to the scanning period prf = duty cycle/pulse width P av = P t X duty cycle = Pt X Pulse width X prf

9 Radar frequency band designations Band designationNominal frequency range Specific radar bands based on ITU assignment HF3 – 30 MHz VHF30 – 300 MHz , MHz UHF300 – 1000 MHz , MHz L1 – 2 GHz MHz S2 – 4 GHz , MHz C4 – 8 GHz MHz X8 – 12 GHz MHz Ku1 2– 18 GHz , GHz K18 – 27 GHz GHz Ka27 – 40 GHz GHz

10 Classification 1. Continuous Wave Radar (CW Radar) or Doppler Radar Continuous Wave (CW) radars utilize Continuous waveforms, which may be considered to be a pure sine wave of the form cos( 2 pi f 0 t). Spectra of the radar echo from stationary targets and clutter will be concentrated at the center frequency f 0 for the echoes from moving targets will be shifted by, the Doppler frequency. Thus by measuring this frequency difference CW radars can very accurately extract target relative velocity. Because of the continuous nature of CW emission, range measurement is not possible without some modifications to the radar operations and waveforms

11 2. Pulsed Radar: More useful than CW radar. Here the Tx transmits a train of narrow rectangular shaped pulses modulating a sine wave carrier. The range to the target is determined by measuring the time taken by the pulse to travel to the target and return to the radar station.

12 Radar range equation Radar range equation relates the range of the radar to the characteristics of the Tx, Rx, antenna, target and the environment. It is used for radar system design. P t = power radiated by an isotropic antenna Power density at a range R from an W/m 2 isotropic antenna.. W/m 2 where G is the directive gain

13

14

15 Amount of power intercepted by the target = σ It is also called the radar cross section of the target It depend on the targets shape, size and composition Total power intercepted by the target W.. Received power, W Where A e is the effective area of the antenna.

16 The maximum range of the radar R max is the distance beyond which the target cannot be detected. This happens when P r = S min, minimum detectable signal. This is called radar range equation

17 Factors effecting range of a radar: Transmitter power Frequency Radar cross-section of the target Minimum received signal power Pr (min) Assignment: Receiver Thermal Noise and Signal to Noise Ratio

18 Maximum Unambiguous Range Once the radar Tx transmits a pulse, sufficient time should be alloted so that the echo signal due to this pulse may be received and detected before the next pulse is transmitted. If the prf is too high echoes may arrive after the transmission of the next pulse. Such echoes are called Second time around echoes

19

20 Pulsed Radar

21 Trigger source Pulse modulator Microwave oscillator Duplexer Low Noise amplifier Mixer and local oscillator IF amplifier Detector and Video amplifier Indicator or display Direction indication from angle data

22 The Doppler Effect The shift in frequency of the received echo signal from a moving target compared to the transmitted frequency of a radar station is called Doppler frequency shift and phenomena is called Doppler effect Let R be the Range of the target The number of wavelengths contained in the two way path between the radar and the target is Total phase shift φ =

23 If the target is moving R and φ changes continuously. Rate of change of φ is angular frequency. Where v r is the relative velocity of the target wrt radar. f d is the Doppler frequency shift. Where

24 Continuous Wave Doppler Radar

25 Tx generates continuous sinusoidal oscillations of frequency f o. It is radiated by the antenna. CW radar receives the echo signal while it transmits. If the target is in motion the received echo signal will be shifted in frequency by an amount f d. ( ) Mixer isolates the Doppler frequency note f d. Beat frequency amplifier eliminates the echoes from stationary targets and amplifies the Doppler echo signal. This radar is also called CW radar with zero IF or CW Super-heterodyne radar with Zero IF or Simple doppler radar or CW homodyne radar.

26 Echoes from natural environment such as land, sea, and weather are called clutter. They are called clutter because they will clutter (untidily crowd) the radar display. Isolation between Tx and Rx: Isolation required depends on Tx power, Tx noise and sensitivity of the receiver Large distance CW radar introduce more Tx noise Transmitter clutter: Tx noise that enters the radar receiver via back scatter from the clutter. False targets: Tx signal is not a pure CW. The associated side bands may mask the desired signals or generated false targets.

27 Limitations of simple CW Radar Lack of isolation between Tx and Rx. Receiver burn out Masking of wanted signals by Tx noise Introduction of flicker noise ( 1/f noise) due to homodyne Lack of matched filter in the receiver Unable to identify whether the target is approaching or receding Increased clutter compared to pulsed radar Measurement of range is not possible

28 CW Radar with Non-zero IF It is not simple as ordinary CW radar.

29 Isolation between Tx and Rx Separate antennas are used for Tx and Rx to reduce Tx leakage Local oscillator in the Rx is derived from the Tx signal mixed with locally generated signal of frequency equal to that of the receiver IF. Tx leakage can occur due to Tx clutter also. Reduction in flicker noise: Flicker effect noise reduces the receiver sensitivity of a CW Radar with zero IF (Simple doppler radar). In order to increase the sensitivity and efficiency we go for CW Radar with Non-zero IF. Doppler frequency usually falls in the audio or video frequency range which is more susceptible to flicker noise. Flicker noise is inversely proportional to frequency. So as we shift the doppler freq to IF flicker noise reduces.

30 Super-heterodyne receiver with non zero IF increases the receiver sensitivity above 30 dB Receiver bandwidth: IF amplifier should be wide enough to pass the expected range of Doppler frequencies. Usually expected range of Doppler frequencies will be much higher than the doppler frequency. So a wide band amplifier is needed. But as bandwidth of Rx in increased noise increases and sensitivity degrades. Also the Tx signal band width is also not narrow. So Rx signal bandwidth again increases.

31

32 SNR can be enhanced by using filter banks for Doppler amplifier. It approximates a matched filter

33 BW of each filter is wide enough to accept the signal energy. But not so wide to accept the noise. The more the filters used less will be the SNR loss and less chance of missing a target Direction of target motion:

34 A simple CW radar loses the sign of doppler shift during mixing. The sign can be obtained by:

35 If the output of channel B leads the output of channel A, the doppler shift Positive. Approaching Target If the output of channel B lags the output of channel A, the doppler shift Negative. Receding Target

36 Applications of CW radar with Non-zero IF Police speed monitor Rate-of-climb meter (During aircraft take off) Vehicle counting As a replacement for 5 th wheel speedometer in vehicle testing Antilock braking system Collision avoidance In railways as speedometer instead of tachometer Advance warning system for approaching targets Docking speed measurement of large ships Intruder alarms Measurement of velocity of missiles, baseball etc

37 Limitations of CW radar with Non-zero IF False targets Unable to detect the range of the target

38 Frequency Modulated CW radar FM CW radar is capable of measuring the relative velocity and the range of the target with the expense of bandwidth. By providing timing marks into the Tx signal the time of transmission and the time of return can be calculated. This will increase the bandwidth More distinct the timing, more accurate the result will be and more broader will the Tx spectrum Here it is done by frequency modulating the carrier and the timing mark is the change in frequency

39 Block diagram: Tx frequency increases linearly with time (solid line)

40 The echo signal will return after a time (dashed line) If the echo signal is heterodyned with a portion of the transmitter signal in a nonlinear element such as a diode, a beat note f b will be produced. If there is no doppler frequency shift, the beat note is a measure of the target's range and f b = f r, If the rate of change of the carrier frequency is, the beat frequency is

41 In practical receivers triangular frequency modulation is used. (b)= Triangular freq modulation (c)= Corresponding beat note

42 If the frequency is modulated at a rate f m over a range Δf the beat frequency is The reference signal from the transmitter is used to produce the beat frequency note Beat frequency is amplified and limited to eliminate any amplitude fluctuations. The freq of the amp-limited beat note is measured with a cycle counting frequency meter calibrated in distance

43 If the target is not stationary doppler frequency shift will be superimposed on the FM range beat note and an erroneous range measurement results

44 The beat frequency due to range f r can be calculated as One-half the difference between the frequencies will yield the doppler frequency. If there are more than one target, the range to each target may be measured by measuring the individual frequency components by using a bank of narrow band filters. If the targets are moving the task of measuring the range of each becomes complicated

45 FM CW Altimeter To measure the height above the surface of the earth FM CW radar is used as aircraft radio altimeter. Low Tx power and low antenna gain is needed because of short range. Since the relative motion between the aircraft and ground is small, the effect of the Doppler frequency shift may usually be neglected. Frequency range: 4.2 to 4.4 GHz (reserved for altimeters) Solid state Tx is used here. High sensitive super-heterodyne Rx is preferred for better sensitivity and stability

46 Block diagram:

47 The output of the detector contains the beat frequency which contains doppler frequency and the range frequency. It is amplified to a level enough to actuate the frequency measuring circuits. The average frequency counter determines the range The switched frequency counter determines the Doppler velocity Averaging frequency counter is necessary in an altimeter, since the rate of change of altitude is usually small

48 In an altimeter, the echo signal from an extended target varies inversely as the square (rather than the 4 th power)of the range, because greater the range greater the echo area illuminated by the beam. Low frequency amplifier is a narrow band filter which is wide enough to pass the received signal energy, thus reducing the amount of noise with which the signal must compete. The average frequency counter is a cycle counter. It counts only absolute numbers. So there may be step errors or quantization errors

49 Unwanted signals in FM altimeter: 1. The reflection of the transmitted signals at the antenna caused by impedance mismatch. 2. The standing-wave pattern on the cable feeding the reference signal to the receiver, due to poor mixer match. 3. The leakage signal entering the receiver via coupling between transmitter and receiver antennas. This can limit the ultimate receiver sensitivity, especially at high altitudes. 4. The interference due to power being reflected back to the transmitter, causing a change in the impedance seen by the transmitter. This is usually important only at low altitudes. It can be reduced by an attenuator introduced in the transmission line at low altitude or by a directional coupler or an isolator. 5. The double-bounce signal.

50

51 MTI and Pulsed Doppler Radar Using the principle of doppler frequency shift in pulsed radar the relative velocity of the target can be determined. A pulse radar that utilizes the doppler frequency shift as a means for discriminating moving from fixed targets is called an MTI (moving target indication) or a pulse doppler radar. MTI is a necessity in high-quality air-surveillance radars that operate in the presence of clutter. Its design is more challenging than that of a simple pulse radar or a simple CW radar.

52 A CW radar is converted to pulsed radar by,

53 The difference between simple pulse radar and pulse doppler radar is that in pulse doppler radar the reference signal at the Rx is derived from the Tx, where as in simple pulse radar the reference signal at the Rx is from a local oscillator. Here the reference signal acts as the coherent reference needed to detect the doppler frequency shift. The phase of the transmitted signal is preserved in the reference signal. Operation: Let the CW oscillator signal be Then the reference signal is,

54 Doppler shifted echo signal can be represented as, The reference signal and the target signal are heterodyned in a mixer and the output is the difference frequency component The difference frequency is the doppler frequency. For stationary targets V diff is a constant. The voltages mentioned above are shown in the fig below.

55

56 Sample waveforms (bipolar)

57 Moving targets may be distinguished from stationary targets by observing the video output on an A-scope (amplitude vs. range). Echoes from fixed targets remain constant throughout, but echoes from moving targets vary in amplitude from sweep to sweep at a rate corresponding to the doppler frequency. The superposition of the successive A-scope sweeps is shown in Fig. The moving targets produce, with time, a " butterfly" effect on the A-scope. It is not appropriate for display on the PPI.

58 Figure (a-e) Successive sweeps of an MTI radar A- scope display (echo amplitude as a function of time); (f) superposition of many sweeps; arrows indicate position of moving targets.

59 Delay line cancelers: One method commonly employed to extract doppler information in a form suitable for display on the PPI scope is with a delay-line canceler The delay-line canceler acts as a filter to eliminate the dc component of fixed targets and to pass the ac components of moving targets.

60 Typical MTI radar (With Power Amplifier)

61 It differs in the way in which the reference signal is generated. The coherent reference is supplied by an oscillator called the coho, which stands for coherent oscillator. The coho is a stable oscillator whose frequency is the same as the intermediate frequency used in the receiver. The output of the coho f c is also mixed with the local-oscillator frequency f l. The local oscillator must also be a stable oscillator and is called stalo, for stable local oscillator. The RF echo signal is heterodyned with the stalo signal to produce the IF signal just as in the conventional super-heterodyned receiver.

62 The characteristic feature of coherent MTI radar is that the transmitted signal must be coherent (in phase) with the reference signal in the receiver. This is accomplished by the coho signal. The function of the stalo is to provide the necessary frequency translation from the IF to the transmitted (RF) frequency. Any stalo phase shift is canceled on reception. The reference signal from the coho and the IF echo signal are both fed into a mixer called the phase detector. Its output is proportional to the phase difference between the two input signals.

63 Triode, tetrode, klystron, traveling-wave tube, and the crossed-field amplifier can be used as the power amplifier A transmitter which consists of a stable low-power oscillator followed by a power amplifier is sometimes called MOPA, which stands for master-oscillator power amplifier.

64 MTI radar (with power-oscillator Tx) In an oscillator the phase of the RF bears no relationship from pulse to pulse. For this reason the reference signal cannot be generated by a continuously running oscillator. However, a coherent reference signal may be readily obtained with the power oscillator by readjusting the phase of the coho at the beginning of each sweep according to the phase of the transmitted pulse. The phase of the coho is locked to the phase of the transmitted pulse each time a pulse is generated.

65

66 A portion of the transmitted signal is mixed with the stalo output to produce an IF beat signal whose phase is directly related to the phase of the transmitter. This IF pulse is applied to the coho and causes the phase of the coho CW oscillation to "lock" in step with the phase of the IF reference pulse. The phase of the coho is then related to the phase of the transmitted pulse and may be used as the reference signal for echoes received from that particular transmitted pulse. Upon the next transmission another IF locking pulse is generated to relock the phase of the CW coho until the next locking pulse comes along.