WS9 -1 NAS105, Workshop 9, May 2005 WORKSHOP 9 DESIGN OPTIMIZATION OF A CANTILEVER BEAM.

Презентация:



Advertisements
Похожие презентации
WS7 -1NAS105, Workshop 7, May 2005 WORKSHOP 7 Large Deflection Analysis of Simply Supported Square Plate.
Advertisements

WS1-1 NAS105, Workshop 1, May 2005 WORKSHOP 1 MODELING RIGID LINK WITH RBE2, MPC, and STIFF BAR.
WS2-1 NAS105, Workshop 2, May 2005 WORKSHOP 2 MODELING WITH INERTIA RELIEF.
WS5 -1 NAS105, Workshop 5, May 2005 WORKSHOP 5 MODEL WITH SOLIDS, PLATES AND BEAMS.
WS4 -1 NAS105, Workshop 4, May 2005 WORKSHOP 4 MODEL WITH PLATES AND BEAMS.
WS6 -1 NAS105, Workshop 6, May 2005 WORKSHOP 6 FLY-SWATTER MODEL for SUPERELEMENTS.
WS8 -1 NAS105, Workshop 8, May 2005 WORKSHOP 8 Analysis of Laminated Composite Plate.
WS13 -1 NAS105, Workshop 13, May 2005 WORKSHOP 13 TRANSIENT DYNAMIC ANALYSIS OF A CAR GOING OVER A BUMP.
WS20-1 NAS122, Workshop 20, August 2005 Copyright 2005 MSC.Software Corporation WORKSHOP 20 CALCULATE RESPONSE SPECTRA.
WS19-1 WORKSHOP 19 EFFECTIVE MASS NAS122, Workshop 19, August 2005 Copyright 2005 MSC.Software Corporation.
WS5-1 PAT328, Workshop 5, May 2005 Copyright 2005 MSC.Software Corporation WORKSHOP 5 ARBITRARY BEAM SECTION.
WS21-1 NAS122, Workshop 21, August 2005 Copyright 2005 MSC.Software Corporation WORKSHOP 21 RESPONSE SPECTRUM ANALYSIS.
WORKSHOP 3 EDITING A NASTRAN INPUT FILE. WS3-2 NAS120, Workshop 3, May 2006 Copyright 2005 MSC.Software Corporation.
WS4-1 PAT328, Workshop 4, May 2005 Copyright 2005 MSC.Software Corporation WORKSHOP 4 SOLID TOPOLOGY OPTIMIZATION.
WS14a-1 WORKSHOP 14A MODAL ANALYSIS OF A TOWER NAS122, Workshop 14a, August 2005 Copyright 2005 MSC.Software Corporation.
S17-1 NAS122, Section 17, August 2005 Copyright 2005 MSC.Software Corporation SECTION 17 ENFORCED MOTION LARGE MASS METHOD.
WS12b-1 WORKSHOP 12B MODAL ANALYSIS FOR PRESTIFFENED TURBINE BLADE AT DIFFERENT RPM y x z 5,000 rpm Fixed edge displacements NAS122, Workshop 12b, August.
S11-1PAT301, Section 11, October 2003 SECTION 11 ANALYSIS SETUP.
WS2-1 PAT301, Workshop 2, October 2003 WORKSHOP 2 CANTILEVERED PLATE.
WS6-1 PAT328, Workshop 6, May 2005 Copyright 2005 MSC.Software Corporation WORKSHOP 6 NESTED COORDINATE SYSTEMS.
Транксрипт:

WS9 -1 NAS105, Workshop 9, May 2005 WORKSHOP 9 DESIGN OPTIMIZATION OF A CANTILEVER BEAM

WS9 -2 NAS105, Workshop 9, May 2005

WS9 -3 NAS105, Workshop 9, May 2005 Tasks n Run the input file workshop9. dat (Optimization Model of a Prismatic Section Cantilever Beam), and study the.f06 file n Modify workshop9.dat, to also include the width of the beam, as a design variable, specifying that the width cant be lower than 0.5, and higher than 2.5

WS9 -4 NAS105, Workshop 9, May 2005 Problem Files n Required File(s): workshop9. dat - Optimization Model of a Cantilever Beam cantbeam.dat - File used as an include file in workshop9. dat n Proposed Solution File(s): ws9s.bdf - Solution File