ELECTRICAL SAFETY OSHA 29 CFR 1910 SUBPART S Bureau of Workers Comp PA Training for Health & Safety (PATHS) 1PPT

AN AVERAGE OF ONE WORKER IS ELECTROCUTED ON THE JOB EVERY DAY! There are four main types of electrical injuries: Electrocution (death due to electrical shock) Electrical Shock Burns Falls 2PPT

CURRENT = The movement of electrical charge. RESISTANCE = Opposition to current flow. VOLTAGE = A measure of electrical force. CONDUCTORS = Substances, such as metals, that have little resistance to electricity. INSULATORS = Substances, such as wood, rubber, glass and bakelite, that have high resistance to electricity. GROUNDING = A conductive connection to the earth which acts as a protective measure. 3PPT

Received when current passes through the body. Severity of the shock depends on: Path of current through the body Amount of current flowing through the body Length of time the body is in the circuit LOW VOLTAGE DOES NOT MEAN LOW HAZARD! 4PPT

Currents greater than 75mA (1/1,000 of an ampere) can cause ventricular fibrillation (rapid, ineffective heartbeat) Will cause death in a few minutes unless a defibrillator is used. 75mA is not much current –a small power drill uses 30 times as much. 5PPT

When two wires have different potential voltages, current will flow if they are connected. In most household wiring the black wires are at 110 volts relative to ground. The white wires are at zero volts because they are connected to ground. Contact with an energized (live) black wire while touching the white grounded wire = ELECTRICAL SHOCK! 6PPT

Contact with an energized wire/any energized electrical component + any grounded object = SHOCK! You can even receive an electrical shock when you are not in contact with a ground. CONTACT BOTH WIRES OF A 240 VOLT CABLE = SHOCK, POSSIBLE ELECTROCUTION! 7PPT

Are the most common shock- related nonfatal injury Occur when you touch electrical wiring or equipment that is improperly used or maintained Typically occurs on the hands Very serious injury that needs immediate attention 8PPT

Electrical shock can also cause indirect or secondary injuries. Employees working in an elevated location who experience a shock can fall, resulting in serious injury or even death. 9PPT

A hazard exists when a conductor is too small to safely carry the current. Example: Using a portable tool with an extension cord that has a wire too small for the tool. Tool draws more current than cord can handle = overheating, possible fire without tripping the circuit breaker Circuit breaker could be the right size for the circuit but not for the smaller wire extension cord Wire Gauge WIRE Wire gauge measures wires ranging in size from number 36 to 0 American wire gauge (AWG) 10PPT

Too many devices plugged into circuit = wires heat to very high temperature = possible fire Wire insulation melts = arcing may occur = fire in area where overload exists (even inside a wall) 11PPT

Shut off electricity flow in the event of an overload or ground-fault in the circuit. Include fuses, circuit breakers and ground- fault circuit interrupters, or CGCI. Fuses and circuit breakers are over current devices (too much current = fuses melt and circuit breakers trip open). 12PPT

Protects you from dangerous electrical shock. Detects a difference in current between the black and white circuit wires (could happen when electrical equipment is not working properly causing a current leakage known as ground fault). Ground fault detected = GFCI can shut off electricity flow in as little as 1/40 of a second protecting you from a dangerous shock. 13PPT

Some of the most frequently violated OSHA standards. Metal parts of an electrical wiring system that we touch should be at 0 volts relative to ground (switch plates, ceiling light fixtures, conduit, etc.). Housings of motors, appliances or tools that are plugged in to improperly grounded circuits may become energized. If you come into contact with an improperly grounded electrical device YOU WILL GET SHOCKED! 14PPT

GROUNDING PATH The path to ground from circuits, equipment and enclosures must be permanent and continuous. The violation shown here is an extension cord with the third/grounding prong missing. 15PPT

HAND-HELD ELECTRICAL TOOLS: Hand-held electrical tools pose a potential danger because they make continuous good contact with the hand. To protect you from shock, burns and electrocution, tools must: Have a 3-wire cord with ground and be plugged into a grounded receptacle Be double insulated Be powered by a low-voltage isolation transformer 16PPT

Must guard live parts of electric equipment operating at > 50 volts against accidental contact by: Approved cabinets/enclosures Location or permanent partitions (thereby only accessible to qualified persons) Elevation of 8 feet or more above the floor or working surface Mark entrances to guarded locations with conspicuous warning signs 17PPT

Where electrical equipment is in locations that it can suffer physical damage it must be guarded. The violation shown here is physical damage to conduit. 18PPT

Junction boxes, pull boxes and fittings must have approved covers. Unused openings in cabinets, boxes and fittings must be closed (no missing knockouts). Photo shows violations of these two requirements. 19PPT

Are more vulnerable than fixed wiring. Should not be used if recognized wiring methods can be used instead. Flexible cords can be damaged by: Aging Door or window edges Staples or fastenings Abrasion from adjacent materials Activities in the area Improper use of flexible cords can cause shocks, burns or fire. 20PPT

Pendant or Fixture Portable lamps, Stationary equipment Wiring tools or appliances to facilitate interchange 21PPT

Substitute for Run through walls, ceilings Concealed behind fixed wiring floors, doors, or windows or attached to building surfaces 22PPT

Tripped circuit breakers or blown fuses Warm tools, wires, cords, connections or junction boxes GFCI that shuts off a circuit Worn or frayed insulation around wire or connection 23PPT

Train employees working with electrical equipment in safe working practices including: De-energizing electrical equipment before inspecting or making repairs Using electric tools in good repair Using good judgment when working near energized lines Using appropriate protective equipment, or PPE 24PPT

Hazards -Inadequate wiring - - Exposed electrical parts - Wires with bad insulation - Ungrounded electrical tools/systems - Overloaded circuits - Damaged power tools/equipment -Overhead power lines -All hazards are made worse in wet conditions! 25PPT

Protective Measures Proper grounding Using GFCIs Using fuses and circuit breakers Proper use of flexible cords Training 26PPT

The bottom line with electricity: RESPECT COMMON SENSE SAFETY 27PPT

28PPT