2.1 Chapter 2 Network Models Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.

LAYERED TASKS We use the concept of layers in our daily life. As an example, let us consider two friends who communicate through postal mail. The process of sending a letter to a friend would be complex if there were no services available from the post office. Sender, Receiver, and Carrier Hierarchy Topics discussed in this section:

2.3 Figure 2.1 Tasks involved in sending a letter

THE OSI MODEL Established in 1947, the International Standards Organization (ISO) is a multinational body dedicated to worldwide agreement on international standards. An ISO standard that covers all aspects of network communications is the Open Systems Interconnection (OSI) model. It was first introduced in the late 1970s. Layered Architecture Peer-to-Peer Processes Encapsulation Topics discussed in this section:

2.5 ISO is the organization. OSI is the model. Note

2.6 Figure 2.2 Seven layers of the OSI model

2.7 Figure 2.3 The interaction between layers in the OSI model

2.8 Figure 2.4 An exchange using the OSI model

LAYERS IN THE OSI MODEL In this section we briefly describe the functions of each layer in the OSI model. Physical Layer Data Link Layer Network Layer Transport Layer Session Layer Presentation Layer Application Layer Topics discussed in this section:

2.10 Figure 2.5 Physical layer

2.11 The physical layer is responsible for movements of individual bits from one hop (node) to the next. Note

2.12 Figure 2.6 Data link layer

2.13 The data link layer is responsible for moving frames from one hop (node) to the next. Note

2.14 Figure 2.7 Hop-to-hop delivery

2.15 Figure 2.8 Network layer

2.16 The network layer is responsible for the delivery of individual packets from the source host to the destination host. Note

2.17 Figure 2.9 Source-to-destination delivery

2.18 Figure 2.10 Transport layer

2.19 The transport layer is responsible for the delivery of a message from one process to another. Note

2.20 Figure 2.11 Reliable process-to-process delivery of a message

2.21 Figure 2.12 Session layer

2.22 The session layer is responsible for dialog control and synchronization. Note

2.23 Figure 2.13 Presentation layer

2.24 The presentation layer is responsible for translation, compression, and encryption. Note

2.25 Figure 2.14 Application layer

2.26 The application layer is responsible for providing services to the user. Note

2.27 Figure 2.15 Summary of layers

TCP/IP PROTOCOL SUITE The layers in the TCP/IP protocol suite do not exactly match those in the OSI model. The original TCP/IP protocol suite was defined as having four layers: host-to- network, internet, transport, and application. However, when TCP/IP is compared to OSI, we can say that the TCP/IP protocol suite is made of five layers: physical, data link, network, transport, and application. Physical and Data Link Layers Network Layer Transport Layer Application Layer Topics discussed in this section:

2.29 Figure 2.16 TCP/IP and OSI model

ADDRESSING Four levels of addresses are used in an internet employing the TCP/IP protocols: physical, logical, port, and specific. Physical Addresses Logical Addresses Port Addresses Specific Addresses Topics discussed in this section:

2.31 Figure 2.17 Addresses in TCP/IP

2.32 Figure 2.18 Relationship of layers and addresses in TCP/IP

2.33 In Figure 2.19 a node with physical address 10 sends a frame to a node with physical address 87. The two nodes are connected by a link (bus topology LAN). As the figure shows, the computer with physical address 10 is the sender, and the computer with physical address 87 is the receiver. Example 2.1

2.34 Figure 2.19 Physical addresses

2.35 As we will see in Chapter 13, most local-area networks use a 48-bit (6-byte) physical address written as 12 hexadecimal digits; every byte (2 hexadecimal digits) is separated by a colon, as shown below: Example :01:02:01:2C:4B A 6-byte (12 hexadecimal digits) physical address.

2.36 Figure 2.20 shows a part of an internet with two routers connecting three LANs. Each device (computer or router) has a pair of addresses (logical and physical) for each connection. In this case, each computer is connected to only one link and therefore has only one pair of addresses. Each router, however, is connected to three networks (only two are shown in the figure). So each router has three pairs of addresses, one for each connection. Example 2.3

2.37 Figure 2.20 IP addresses

2.38 Figure 2.21 shows two computers communicating via the Internet. The sending computer is running three processes at this time with port addresses a, b, and c. The receiving computer is running two processes at this time with port addresses j and k. Process a in the sending computer needs to communicate with process j in the receiving computer. Note that although physical addresses change from hop to hop, logical and port addresses remain the same from the source to destination. Example 2.4

2.39 Figure 2.21 Port addresses

2.40 The physical addresses will change from hop to hop, but the logical addresses usually remain the same. Note

2.41 Example 2.5 As we will see in Chapter 23, a port address is a 16-bit address represented by one decimal number as shown. 753 A 16-bit port address represented as one single number.

2.42 The physical addresses change from hop to hop, but the logical and port addresses usually remain the same. Note